Tank Level Sensing PUT-FSW-xx.x and TSI-10   Click on image to enlarge
	The PUT-FSW-xx.x is a flange mount pickup tube designed for installation in the side wall of a tank. The xx.x represents tube length in inches cut at factory. The TSI-10 is the tank level interface wired to MCP. For tank depths to 40". See TSI-50 for tanks to 200".	$99.00ea.

Tank Level Sensing PUT-F-xx and TSI-10   Click on image to enlarge
	The PUT-F-xx is a flange mount pickup tube designed for tanks without welded in threaded hubs. xx represents tube length in inches cut at factory. The TSI-10 is the tank level interface wired to MCP. For tank depths to 40". See TSI-50  for tanks to 200".	$99.00ea.

Tank Level Sensing PUT-H-xx and TSI-10     Click on image to enlarge
	The PUT-H-xx is a Hub mount pickup tube designed for tanks with welded in threaded hubs. xx represents tube length in inches cut at factory. The TSI-10 is the tank level interface wired to MCP. For tank depths to 40". See TSI-50 for tank depths to 200"	$99.00ea.

Tank Level Sensing PUT-F-xx and TSI-50   Click on image to enlarge
	The PUT-F-xx is a flange mount pickup tube designed for tanks without welded in threaded hubs. xx represents tube length in inches cut at factory. The TSI-50 is the tank level interface wired to MCP. For Tanks between 40" and 200".	$99.00ea.

Tank Level Sensing PUT-H-xx and TSI-50    Click on image to enlarge
	The PUT-H-xx is a Hub mount pickup tube designed for tanks with welded in threaded hubs. xx represents tube length in inches cut at factory. The TSI-50 is the tank level interface wired to MCP. For tanks between 40" and 200" deep.	$99.00ea.

Temperature Sensing Interface            TMSI-F1          Click on image to enlarge
	The TMSI-F1 Temperature sensing interface calibrated in degrees fahrenheit.	$49.00ea.

AC Voltage Sensing Interface           ACVSI-120        Click on image to enlarge
	The ACVSI-120 The AC voltage sensing interface includes both L1 and L2 sensing. It comes with a 3ft cable for wiring to circuit breakers (Not included) in the distribution panel. Optical isolation in the interface assures no line voltages on the control wiring.	$119.00ea.

AC Current Sensing Interface            ACISI-50        Click on image to enlarge
	The ACISI-50 The AC current sensing interface includes a 50amp donut CT for monitoring current levels in one leg of the AC supply line. For monitoring in both L1 and L2 you will need two.  The ACSI-50 is required for the load shedding option of the MCP-500-RV.	$83.00ea.

AC Current Sensing Interface            ACISI-100       Click on image to enlarge
	The ACISI-100 is used in vessels using 100 amp 120/250 volt services. It includes a 100 amp donut CT for monitoring current levels in one leg of the AC supply line. For monitoring in both L1 and L2 you will need two.  Two ACSI-100 or 50's are required for the load shedding option of the MCP-500-RV.  Contact factory for vessels with three phase service.	$129.00ea.

DC Voltage Sensing Interface            DCV-12        Click on image to enlarge
	The DCV-12  is the DC voltage sensing interface for both the house and engine battery banks	$42.00ea.

DC Voltage Sensing Interface            DCV-24      Click on image to enlarge
	The DCV-24  is the DC voltage sensing interface for both the house and engine battery banks where the banks are 24 volt.	$42.00ea.

DC Current Sensing Interface            DCI-200          Click on image to enlarge
	The DCI-200 includes a 200amp DC shunt for monitoring the house battery bank current draw.	$49.00ea.

Propane Tank Level Sensing Interface                     PSI-90                 Click on image to enlarge
	The PSI-90 is an interface between a standard 0-90 ohm Rochester Gauges Twin Site sender and the processor. The gauge is shown in the photo for clearification purposes only and is not supplied with the interface. They are easily puchased from your local gas company if your tank does not already have one.	$37.00ea.

AC Power Sensing Module                     ACSM-3                            Click on image to enlarge
	The ACSM-3 is a power sensing module that connects in to power points at  the automatic transfer switch.   It lets the MCP know where and if power is being supplied from the generator or shore power and is used in conjunction with the GSM-2 for the automatic control of the generator.	$89.00ea.

Generator Starting Module                     GSM-2             Click on image to enlage
	The GSM-2 is used to start and stop the generator automatically. It is designed to be used with any generator with automatic shutdowns and momentary glow, start and stop controls. The ACSM-3 is also required for automatic generator control.	$75.00ea.

Load Shedding Module               LSM-2      Click on image to enlage
	The LSM-2 is the load shedding module that allows the MCP to switch non-essential loads of up to 20 amps off when an overload condition occurs.  It can switch two circuits one on line 1 and one on line 2. The LSM-2 also includes control switching for back-up heating.	$95.00ea.